Exmark LZS691CKA52400 Lazer Z Mower 52 Inch

In-Store Pickup Only Exmark LZS691CKA52400 Lazer Z Mower 52 Inch

Financing available, first 120 days no payment. After 120 days (48 months no interest)

 https://secure.sheffieldfinancial.com/newLoanApplication.aspx

More power. More features. More productivity. 

Engine
Engine ManufacturerKawasaki®
Engine TypeFX691V
Displacement726 cc
General
TransmissionHydro-Drive
Wheel SizeFront: 13 x 5.0-6; Drive: 23 x 9.5-12
Fuel Capacity12 gal. (45.4 L)
Deck
Deck Size52 in.
Discharge TypeSide; Optional: Bag, Mulch

With the S-Series, you can choose from eight different engines, including an eco-friendly, Electronic Fuel Injection (EFI), propane option. Four UltraCut™ Series 4 cutting deck sizes are available with widths up to 72 inches. Want tough, try a 10-guage, formed and continuously seam-welded top and a 7-guage side skits. All with welded spindle mounting sites and full-floating 4-point suspension with four adjustable anti-scalp rollers.

    Features
    • Doing More With Propane: Our EFI system optimizes fuel delivery in real-time, which improves efficiency and performance. This, in combination with lower propane cost reduces operating expenses versus typical gas-powered mowers.
    • Less Time At The Pump: Gas-powered S-Series models have a single 12-gallon tank with one fill location.
    • Built to Last: Want tough? Try a 10-gauge, formed and continuously seam-welded top, and a 7-gauge side skirt. All with welded spindle mounting sites. And, full-floating, 4-point suspension with four adjustable anti-scalp rollers.
    • On-Board Diagnostics: Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.
    • Fewer Grease Points: With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Greaseless spindles and only four grease points on the entire machine.
    • Ultracut Series 4 Deck: This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.
    • Tool-less Belt Removal: Deck and hydro belt can be installed without using any tools.
    Decks
    • Blade Tip Speed: Approximately 18,500 fpm.
    • Blades: 3 Blades at 18.00" Length
    • Cutting Heights: 1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator’s seat.
    • Deck Construction: 10-gauge top that is formed and continuously seam welded, 7-gauge side skirt and 7-gauge reinforced spindle mounting locations for improved strength and reduced weight.
    • Deck Style: Floating Deck
    • Deck Style Description: Full-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch.
    • Width / Cutting Deck: 52"
    Dimensions
    • Height: 70 in. (177.8 cm)
    • Length: 79.2 in. (201.2 cm)
    • Width: 64.8 in. (164.6 cm)
    • Curb Weight: 1104
    Equipment
    • Blade Spindles: No maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 25mm (.98") diameter spindle shaft and splined blade driver.
    • Cup Holder: Standard
    • Drive Tires: 23 x 9.5-12, 4 ply Turf Master®
    • Electrical: 12-volt battery with 15-amp alternator.
    • Front Caster Tires: 13 x 5.0-6, smooth-tread, semi-pneumatic.
    • Mower Size: full
    • Parking Brake: Lever-actuated disc brake.
    • Seat: Deluxe, two tone, bolstered seat with Elastomeric Vibration Control material. Mounted on innovative Seat Isolation System that provides operator isolation in all three planes of motion as well as fore-aft slide and seat flip-up.
    • Steering Control: Hydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions.
    • Tractor Frame: Unibody, welded, heavy-duty 1.5" x 3" tubular steel.
    Power Components
    • Air Filter: Heavy-duty canister air filtration system
    • Carb Compliant: Yes
    • Casters: .50" thick caster yoke arms.
    • Deck Lift: Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
    • Drive: Hydro-Drive
    • Drive Description: Two Exmark exclusive Parker unitized pump and wheel motor systems with no hoses, integrated cooling fans, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12 cc pumps and 14. 5 cubic inch motors.
    • Drive Wheel Release: Allows unit movement without engine running.
    • Engine Brand: Kawasaki®
    • Engine Displacement: 726
    • Engine Model: FX691V
    • Engine Series: V-Twin
    • Engine Speed: 3,750 rpm
    • Engine Type: Carbureted
    • Fuel Capacity: 12-gallon (45.4-L), single fuel tank with single fill location.
    • Fuel Indicator: Yes - electronic Sender
    • PTO Engagement: MagStop electromagnetic 200-ft-lb clutch with spot brake
    • ROPS: 2-post foldable ROPS standard with seat belt and latch.
    • Safety Package: Operator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators.
    • Speed: Infinitely variable speed selection from 0-10.0 mph (16 kmph) forward, 0-6.0 mph (9.7 kmph) reverse.
    • Fuel Type: Gas Carbureted


    General
    Power source Gas
    Application Commercial
    Inventory
    Condition New

    Write a review

    Note: HTML is not translated!
        Bad           Good

    • Views: 15746
    • Brand: eXmark
    • Product Code: LZS691CKA52400 Lazer Z Mower 52 Inch
    • Availability: In-Store Pickup Only
    • $10,999.00

    With a high powered low-emission engine, the FS 100 RX STIHL trimmer is designed for professional de..
    $359.95